Skip to main content

Datasheet

Hardware Specification​

Product Spec Table​

CategoryDescription
MCU (RP2040)ARM Cortex-M0+ Dual Core133Mhz maximum frequency
264KB on-chip SRAM
16KB on-chip ROM
2MB External ROM
2 × UART, 2 × SPI controllers, 2 × I2C controllers, 16 × PWM channels
1 × USB 1.1 controller and PHY, with host and device support
8 × Programmable I/O (PIO) state machines for custom peripheral support
Ethernet (W5100S)Hardwired TCP/IP With MAC and PHYSupport Hardwired Internet protocols
TCP, UDP, WOL over UDP, ICMP, IGMPv1/v2, IPv4, ARP, PPPoE
Support 4 independent SOCKETs simultaneously
Support SOCKET-less Command
ARP-Request, PING-Request
Internal 16Kbytes Memory for TX/RX Buffers
10BaseT/100BaseTX Ethernet PHY Integrated
SerialInterfaceUART (LVTTL 3.3V) only for debug
SWD
RS232C
SerialSignalTXD, RXD, RTS, CTS, GND
SWCLK, SWDIO
SerialParametersParity: None, Odd, Even
Data bits: 7, 8 bit
Flow control: None, RTS / CTS
SerialSpeedTBD

WIZ510SR-RP Callout​

WIZ510SR-RP Callout
TOP
WIZ510SR-RP Bottom
BOTTOM

WIZ510SR-RP Pinout​

WIZ510SR-RP Pinout

WIZ510SR-RP indicators​

WIZ510SR-RP LED indicators

Pin NumberPin NameSignalDescription
1LD1Power LED(Red)Power on LED
2LD2TCP_STATUS LED(Green)ON : Connect
OFF : Disconnect
3LD3LINK_STATUS LED(Green)ON : LINK
OFF : Unlink
4LD4BLINK LED(Green)Working indicate
When Module working well Blinking every 1.0s

Schematic & Artwork​

H/W versionTypeFiletypeDownload LinkRemarks
1.0TTLAltium Download-
::::::PDF Download-

Part list​

H/W versionTypeFiletypeDownload LinkRemarks
1.0TTLExcel Download-
::::::PDF Download-

Electrical Characteristics​

Operating Conditions​

SymbolParameterMinTypMaxUnit
VccOperating Voltage3.1353.33.465V
VssGround050mV
fFCLKInternal CPU clock frequency--133MHz
TstgStorage Temperature (max)-2085℃
TAAmbient operating temperature-2085℃
VIHInput high voltage2.5V
VILInput low voltage0.6V
VOHOutput high voltage
(High driving strength Current load = 6mA)
(Low driving strength Current load = 3mA)		2.83V
VOLOutput high voltage
(High driving strength Current load = 6mA)
(Low driving strength Current load = 3mA)		0.32V

Ethernet Power Dissipation​

ConditionMinTypMaxTolUnit
100M Transmitting-130mA

External Flash Memory​

SymbolParameterMinUnit
NENDSector Endurance100,000Cycles
TDRData Retention20Years

Connector Specification​

Magnetic RJ45 modular jack (P1)​

WIZ510SR-RP Magnetic RJ45 modular jack (P1)

  • If there is no Ethernet connection, the WIZ510SR-RP device will enter into a continuous reset loop.

2Ø DC-JACK (P2)​

WIZ510SR-RP 2Ø DC-JACK (P2)

  • 5V input

DB9M Serial Interface (J2)​

WIZ510SR-RP Serial Interface (J2)

WIZ510SR-RP DB9M

Pin NumberSignalDescription
1DCDNC
2RXDReceive Data
3TXDTransmit Data
4DTRNC
5GNDSystem Ground(Signal Ground)
6DSRNC
7RTSRequest To Send
8CTSClear To Send
9RINC
  • RXD, TXD, GND: These are all you need if the device does not use hardware handshaking.
  • RXD, TXD, GND, RTS, CTS: These are the signals used when serial device uses hardware handshaking.
  • DCD, DTR, DSR, RI: Not used

1x4 Download (J5)​

WIZ510SR-RP 1x4 Download (J5)

Pin NumberSignalDescription
1VCCSystem Power input (3.3V)
2USB_DPUSB DP Signal input for RP2040
3USB_DMUSB DM Signal input for RP2040

1x6 UART0, SWD (J1)​

WIZ510SR-RP 1x6 UART0, SWD (J1)

Pin NumberSignalDescription
1VCCSystem Power input (3.3V)
2TXUART0_TX (Debug)
3RXUART0_RX (Debug)
4SWCLKSWDCLK
5SWDIOSWDIO
6GNDSystem Ground
  • J1 is not mounted

1x2 BOOT MODE (J3)​

WIZ510SR-RP 1x2 BOOT MODE (J3)

Pin NumberSignalDescription
1BOOT MODEBoot Mode Select signal input
Active Low
Drive this pin low and reset(or power on),then WIZ510SR-RP will enter Boot mode
2GNDSystem Ground
  • J3 is not mounted

1x2 FACT RST (J4)​

WIZ510SR-RP 1x2 FACT RST (J4)

Pin NumberSignalDescription
1FACT RSTFactory Reset Signal input
Drive this pin to Low for at least 5.0s then WIZ510SR-RP will be reset to factory settings
2GNDSystem Ground
  • J4 is not mounted

Switch Specification​

Reset Switch (SW1)​

WIZ510SR-RP Reset Switch (SW1)

  • Pressing SW1 will initiate a reset of the WIZ510SR-RP device.

BOOTSEL Switch (SW2)​

WIZ510SR-RP BOOTSEL Switch (SW2)

  • Pressing SW2 and resetting (or powering on) will cause the RP2040 to enter USB Mass Storage Device mode. This enables the RP2040 to be reprogrammed.

HW TRIG Switch (SW3)​

WIZ510SR-RP HW TRIG Switch (SW3)

  • Slide SW3 Left : AT command
  • Slide SW3 Right : Gateway Mode
  • Changes will be reflected after reset

Dimension​

  • WIZ510SR-RP Rev1.0 Dimension :
    • 63mm x 45mm x 1.6mm ( PCB board size )
    • 76mm x 45mm x 15mm ( Included part size )

WIZ510SR-RP Dimension