Skip to main content

WIZ750SR-110 Datasheet

Hardware Specification​

Product Spec Table​

CategoryDescription
MCUARM Cortex-M0 CoreW7500
48Mhz maximum frequency
Internal 8Mhz RC Oscillator
Flash: 128KB
Large flexible-size SRAM buffer for various User Application
- Min 16KB available if full 32KB socket buffer used
- Max 48KB available if no socket buffer used
ROM for boot code: 6 KB
Hardwired TCP/IP Core8 independent Sockets
SRAM for socket: 32KB
MII (Medium-Independent Interface)
TCP/IP Protocols: TCP, UDP, ICMP, IPv4, ARP, IGMP, PPPoE
PHYTransceiverIP101GRI
Single 10/100M Ethernet Transceiver
SerialSignalTXD, RXD, RTS, CTS, GND
ParametersParity: None, Odd, Even
Data bits: 7, 8 bit
Flow control: None, RTS / CTS, XON / XOFF
SpeedUp to 230Kbps
Dimension62mm x 40mm (PCB board size)
62mm x 40mm x 18mm (Include part size)
Connector typeRJ-45(Ethernet Connector)
D-sub9 Connector(RS-232C)
Input VoltageDC 5V, 100mA under
Temperature-40℃ ~ 85℃ (Operation), -40℃ ~ 85℃ (Storage range)

WIZ750SR-110 Callout​

TOP
BOTTOM

WIZ750SR-110 Pinout​

WIZ750SR-110 indicate​

Pin NumberPin NameSignalDescription
1LD1UART0 RXUART receiver indicate
2LD2UART0 TXUART Transceiver indicate
3LD3Status_LED0PHY LINK check or initialize done
4LD4Status_LED1TCP Connection
5LD5STATUSNot function
6LD6COLCollision Detected
7LD7Power LED-

WIZ750SR-110 Block Diagram​

Schematic & Artwork​

WIZ750SR-110​

H/W versionTypeFiletypeDownload LinkRemarks
1.0RS232Altium Download-
::::::PDF Download-

Part list​

WIZ750SR-110​

H/W versionTypeFiletypeDownload LinkRemarks
1.0RS232Excel Download-
::::::PDF Download-

Electrical Characteristics​

Operating Conditions​

SymbolParameterPinsMinTypMaxUnit
VccOperating Voltage3.3V3.1353.33.465V
VssGroundALL050mV
fFCLKInternal CPU clock frequencyALL0-48MHz
TstgStorage Temperature (max)ALL-4085℃
TAAmbient operating temperatureALL-4085℃
VIOI/O Signal voltage (Tolerance)ALLVss-0.33.35V
VIHInput high voltageALL2.5V
VILInput low voltageALL0.6V
VOHOutput high voltage
(High driving strength Current load = 6mA)
(Low driving strength Current load = 3mA)		ALL2.83V
VOLOutput high voltage
(High driving strength Current load = 6mA)
(Low driving strength Current load = 3mA)		ALL0.32V

Flash Memory​

SymbolParameterMinUnit
NENDSector Endurance10,000Cycles
TDRData Retention10Years

EEPROM​

SymbolParameterMinUnit
NENDSector Endurance1MCycles
TDRData Retention200Years

Connector Specification​

Data D-SUB9 Connector (P2)​

Pin NumberSignalDescription
1DCDNC
2RXDReceive Data
3TXDTransmit Data
4DTRNC
5GNDSystem Ground(Signal Ground)
6DSRNC
7RTSRequest To Send
8CTSClear To Send
9RINC
  • WIZ750SR-110 supports only 4 signals. (TXD, RXD, CTS, RTS)
  • If you want to use all 9 signals, you have to make them separately. or you must design new hardware
  • TXD, RXD, CTS, RTS are provided as peripheral functions.
  • And already made DSR and DTR signal in GPIO functions.(WIZ750SR Firmware code)
  • Therefore, DCD and RI functions must be created.
  • RXD, TXD, GND: These are all you need if the device does not use hardware handshaking.
  • RXD, TXD, GND, RTS, CTS: These are the signals used when serial device uses hardware handshaking.
  • DTR, DSR: Not used

BOOT Pin (J4, J5)​

PartsPin NumberSignalDescription
J41APP BOOTApplication Jump at BOOT mode
:::2GNDSystem Ground
PartsPin NumberSignalDescription
J51BOOTSystem Ground
:::2VCCSystem Power (3.3V)

SWD(JTAG) Pin (J3)​

Pin NumberSignalDescription
1VCCSystem Power (3.3V)
2SWDIOSWD(JTAG) Data I/O pin
3SWCLKSWD(JTAG) Clock pin
4nRESETSystem Reset signal (Active Low)
5GNDSystem Ground

ISP Port & Expansion GPIO (J1, J2)​

PartsPin NumberSignalDescription
J11VCCSystem Power (3.3V)
:::2Expansion GPIODExpansion User's depend on GPIO port
:::3Expansion GPIOC:::
:::4Expansion GPIOB:::
:::5Expansion GPIOA:::
:::6GNDSystem Ground
PartsPin NumberSignalDescription
J21VCCSystem Power (3.3V)
:::2BOOTBOOT SW
:::3U_TXD2Simple UART2(Debug port)
ISP mode firmware downloader port
:::4U_RXD2Simple UART2(Debug port)
ISP mode firmware downloader port
:::5nRESETSystem Reset signal (Active Low)
:::6GNDSystem Ground

RJ-45 Connector (BS-RB10005)​

Pin NumberPinSignal
1R1TX+
2R2TX-
3R3TCT/RCT(Center tap)
4R7RX+
5R8RX-
6L1+(Active LED)Anode
7L2- (Active LED)Cathode
8L3+(LINK LED)Anode
9L4- (LINK LED)Cathode

Dimension​

  • WIZ750SR-110 Rev1.0 Dimension :
    • 63mm x 45mm ( PCB board size )
    • 75mm x 45mm x 18mm ( Included part size )