Skip to main content

Configuration Tool(Chn)

Configuration Tool#

Description#


WIZ550S2E Configuration tool is an application program which is based on java and can be used in most OS platforms including Windows, MAC OS and Linux. Please download .jar file and execute it over Java Virtual Machine.

WIZ550S2E Configuration tool consists four sections

  1. Common Configuration Section
  2. Network Configuration Section
  3. Serial Configuration Section
  4. Option Configuration Section

Common Configurations#

Search#

The Search function is used to search for all existing modules on the same LAN. By using UDP broadcast, it finds all modules on the same subnet, and found devices will be listed in the “Serial to Ethernet” tree(Search Window) with its MAC address.

Setting#

This function is used to apply your configurations.
When you select the MAC address from the “Search Window”, the default value of the module will be displayed. Modify your configurations and click “Setting” button to apply your settings. The module will re-initialize and save the changed configurations.
Users can change the configurations by following the steps below.

1. Select the MAC address of the device which you would like to modify in the “Search Window”
2. Modify the settings according to your needs
3. Click the “Setting” button and then "Password Input Windows" pop up
- Default Password is "WIZnet"
4. Input "Setting Password" and Click "OK" button
5. The module will be initialized by a re-booting process
6. To verify your settings, please click ‘Search’ button and view your new settings

F/W Uploading#

Firmware will be uploaded through TFTP. Click "F/W Uploading" Button and then pop up windows following figures.

Server IP : TFTP Server IP

Server Port : TFTP Server Port (TFTP default Port : 69)
File Name : Firmware File Name
Password : Setting Password

☞ WIZ550S2E Configure tool is not supported TFTP server. So you use TFTP program separately.

Reset#

This is the function which makes WIZ550S2E reboot. This requires "Setting Password".

Factory Reset#

All setting value is initialized to factory default, if the “Factory Reset” button is clicked. Factory default values of WIZ550S2E are listed below.
^ Category ^ Item ^ Value ^

NetworkLocal IP192.168.11.100
:::Local Gateway192.168.11.1
:::Local Subnet255.255.255.0
:::Local Port5000
:::Remote Port5000
:::Working ModeTCP Server
:::Inactivity0
:::Reconnection1000
SerialBaud Rate115200
:::Data Bits8
:::ParityNONE
:::Stop Bits1
:::FlowNONE
:::AT Command USEEnable
:::Trigger Code2B/ 2B / 2B
:::Packing Condition Time0
:::Packing Condition Size0
:::Delimeter Length0
:::Delimeter2D / 2D / 2D / 2D
:::Delimeter Appendix0
OptionsModule NameWIZ550S2E
:::Setting PasswordWIZnet
:::Connection PasswordWIZnet
:::DHCP USEDisable
:::DNS USEDisable
:::DNS Server IP8.8.8.8

Exit#

Close the configuration tool program window.

Search Window#

If you click the “Search” button, all MAC addresses on the same subnet will be displayed.

Search Method#

Reserved

Firmware Version#

It displays the firmware version.

Network Status#

This field shows the current status of network connection.

Connected : This means that TCP connection is established.
Disconnected : This measn that TCP connection is disconnected.
UDP : This means that UDP mode is used.

Network Configurations#

IP#

This section is for setting WIZ550S2E mode's network information

IP:
WIZ550S2E's IP Address
Gateway:
WIZ550S2E's Gateway Address
Subnet mask:
WIZ550S2E's Subnet Mask
Host IP:
Peer system's IP address which WIZ550S2E connects(or sends) to,
when its operating mode is "Client mode","Mixed mode" or "UDP mode".

☞ If you are unclear about your Local IP, Subnet Mask, Gateway information, you have to get this information from your network administrator. If the IP address is not correct, IP collision or network problems may occur.

Port#

This section is for setting WIZ550S2E's Port information.

Local port :
WIZ550S2E's local port number
Remote port :
Peer system socket's port number which WIZ550S2E connects(or sends) to ,
when its operating mode is "Client mode","Mixed mode" or "UDP mode".

Working Mode#

Client / server / mixed TCP establishes connection before data communication, but UDP processes the data communication without connection establishment. The network mode of WIZ550S2E can be divided into TCP Server, TCP Client and Mixed mode according to the connection establishing method. During TCP server mode, WIZ550S2E operates as the server and waits for the connection trial from the client. WIZ550S2E operates as the client in TCP Client mode and tries to connect to the server’s IP and Port. Mixed mode supports both Server and Client. The communication process of each mode is as below.

TCP server mode communication#

During the TCP Server mode, WIZ550S2E waits for the connection request. TCP Server mode can be useful when the monitoring center attempts to connect to the device, while WIZ550S2E is installed, in order to check the status or provide commands. Normally WIZ550S2E is on the waiting status, and if connection request (SYN) from the monitoring center is received, the connection is established (ESTABLISH), and data communication is processed (Data Transaction), and finally connection is closed (FIN). In order to operate this mode, “Device IP”, “Subnet mask”, “Gateway” and “Local port” should be configured first.

For TCP server mode communication, all network configurations including Local IP, Subnet, Gateway and Local port number should be set correctly.

The Data transmission proceeds as below.

  1. The host connects to the WIZ550S2E which is configured as TCP Server mode.
  2. As the connection is established, data can be transmitted in both directions
(host -> WIZ550S2E / WIZ550S2E -> host)

TCP client mode communication#

If WIZ550S2E is set as TCP Client, it tries to establish connection to the server. To operate this mode, “Device IP”, “Subnet mask”, “Gateway”, “Remote host”, and “Remote port” should be set. If “Remote host” has a domain name, you should use the “DNS server” field. In TCP Client mode, WIZ550S2E can actively establish a TCP connection to a host computer when power is supplied.

The Data transmission proceeds as below:

  1. As power is supplied, WIZ550S2E board operating as TCP client mode actively establishes a connection to the server.
  2. If the connection is complete, data can be transmitted in both directions
(host -> WIZ550S2E / WIZ550S2E -> host)

Mixed mode Communication#

In this mode, WIZ550S2E normally operates as TCP Server and waits for the connection request from the peer. However, if WIZ550S2E receives data from the serial device before connection is established, it changes to the client mode and sends the data to the server IP. Therefore, during mixed mode, the server mode is operated prior to the client mode.
Like TCP Server mode, the Mixed mode is useful in case where the monitoring center attempts to connect to the serial device, while WIZ550S2E is used, to check the device status. In addition to this, if any emergency occurs in the serial device, the module will change to Client mode to establish the connection to the server and deliver the emergency status of the device.

UDP mode Communication#

UDP is not a connection oriented protocol but the communication port should be defined well. If UDP mode is selected, the data from serial interface can be defined where to deliver via the “Remote host” and “Remote port.” The WIZ550S2E can also be defined where to receive Ethernet data from via the “Remote host” and “Local port” definition.
If the data destination and source are the same, the two IP addresses will also be the same. Please note that the destination and source are using the same port.

Timer#

Inactivity#

When there is no data transmission, the connection will close automatically after the specified inactivity time. If the default value ‘0’ is set as the Inactivity time, the network connection is maintained even though there is no data transmission. In this case, you should use the ‘Close’ command to close the connection.
This function is useful when there are two or more systems connected to the WIZ550S2E module. If one system is connected to the WIZ550S2E, other systems cannot connect to the module simultaneously. Therefore, the inactivity time should be set and the other system can connect to the module after the inactivity time is elapsed.
Inactivity Time can also be used if the server system unexpectedly shuts down. In this case, there is no data communication, and WIZ550S2E will close the connection and enter into waiting state if the defined inactivity time elapses.

Reconnection#

This is the interval time which WIZ550S2E tries to connect again after connection is closed. This is valid only in "Client mode" or "Mixed mode" having data from serial prior to TCP connection is established.


Serial Configurations#

USART#

This menu is used for setting the serial port.
Baud Rate :

WIZ550S2E's Baud Rate
Data Bits :
WIZ550S2E's Data Bits (7,8,9)
Parity :
WIZ550S2E's Parity Bits
Stop Bits :
WIZ550S2E's stop Bits
Flow :
WIZ550S2E's Flow Control & RS422/RS485

AT Command#

This function is for module configuration through network with the configuration tool serial communication. The serial command mode is enabled as default.

Packing Conditions#

Normally, data received from UART are sent to Ethernet immediately. But in many cases, users want to send data as a chunk of the whole frame without separated ones. This option is for packetizing data into one frame.

Time (0 ~ 65535 ms, ‘0’: Function Disable) :
This field is for specifying time value to judge whether one frame
is received totally. If the time specified in this field is expired
after receiving one byte, then WIZ550S2E notice one data frame is finished,
make an Ethernet packet with all data in its serial buffer and send it to
the peer system via Ethernet.
If WIZ550S2E receives another byte from UART before the specified time is expired,
it restart timer and add the received one to the end of serial data buffer.
Size (0 ~ 255 byte, ‘0’: Function Disable) :
This field is for specifying size value to judge whether one frame is
received totally. If the size specified in this field is received, then WIZ550S2E
notice one data frame is finished, make an Ethernet packet with specifying size's
data in its serial buffer and send it to the peer system via Ethernet.
Char :
This field is for specifying delimiter value to judge whether one frame is received
totally. Char delimiters can be set up to 4 bytes in HEX and valid character count is decided
according to the value in Length field. In case the value of Length field is '0',
this option becomes inactivated.
Appendix is another option for this. If user selects any value in Appendix field, WIZ550S2E make
an ethernet packet with all received data by Char delimiter and next bytes in counts,
which designated by Appendix field.
When Appendix is set with any value, not '0', even though WIZ550S2E received Char delimiters,
it will wait until it receives next data.

Options Configurations#

Module Name#

The device name is displayed in this area.
User can use this name to distinguish this module with others

Password#

This is password field for authentication.

Setting Password :
Configure Tool Setting Password. Critical functions like "Setting", "Firmware Upload",
"Reset" and "Factory Reset" need this password to try issued action and avoid
unauthorized users' command.
When user wants to change its default Setting Password with new one, put new one in this field.
Connection Password :
When WIZ550S2E is tcp server, it needs connection password to check whether client is
an unauthorized user or not. After Client is connected, it must transfer correct
"Connection Password" within 3 seconds. Otherwise, WIZ550S2E will close its TCP connection.

DHCP#

This decides how to obtain IP address. If user selects "Use DHCP" then WIZ550S2E will obtain IP address dynamically by DHCP operation. Otherwise, it will operate in static mode.

Static mode :
If user uses this mode by deselecting "Use DHCP",
user has to set WIZ550S2E with specific network information.
1) First, select "MAC address" in "Search Windows"
2) Then, IP setting section will be activated
3) Fill those fields with information which user want to set.
4) And press "Setting" button then network information will be changed with value user entered.
DHCP mode :
WIZ550S2E's network information will be set automatically without user's interference.

DNS#

This is valid in TCP Client mode only. Normally, TCP Client mode has to know its peer system's IP address. But there are some cases where the IP address is unknown and especially when the IP address change frequently.
In this case, DNS function is needed.

User has to select “Use DNS” option and set DNS Server IP address and peer systems' Domain name in string. Put DNS Server IP, provided by ISP, into “DNS Server IP” field and peer system's Domain name into “Domain” field.